Fashionable Ethnic Style

Send

Multi-colored embroidery, pompons, brushes, tucks, puffs, rosans, cords, braid and ribbons - how amazing all these details are!

It is not surprising that fashion is constantly returning to them, beating in every possible way in women's and men's wardrobes and accessories ...
Today we show how to sew Bavarian (Tyrolean) skirt-sundecorated with original frog mouth ruffles made of silk or rep ribbon.

SO FURTHER "FROGER ROTICS" Sew
STEP 1 On the tape, lay the same folds - "squares" close to each other.
STEP 2 Each pin fold with a pin in the direction transverse to the seam.
STEP 3 In the middle of the tape, sew a stitch, remove the pins, in the middle of each fold sew the edges of the tape with one hand stitch.

AND THEN SITS A SKIRT-SUN IN BAVARIAN STYLE
A wide rep ribbon serves as a belt for her, the panels are decorated with multi-colored braid, mirror sequins and pearl beads.
Stylist's advice: such skirts in everyday life go well with embroidered vests and white blouses or turtlenecks, as well as woolen jackets with jacquard ornaments or cropped jackets made of thick cloth. She can also be worn with a furry vest and a wide leather belt.Sizes: 34-44
Length 70 cm
YOU WILL NEED Woolen fabric in a diagonal rib 1.70-1.75-1.80-1.85-1.90 m long and 150 cm wide; rep ribbon for a belt 1.40-1.45-1.55-1.60-1.70-0.80 m long and 4 cm wide; 1secret zipper 22 cm long and a special presser foot for attaching it; 1 button; rep ribbon, braid and braid otter - approx. 16 pieces approx. 3,50 m of different colors and different widths; rep or silk ribbon for ruffled "frog mouths" 8.80-8.90.90-9.00-9.20-9.30-9.40 m long and 3 cm wide; pearl beads 3.50 m long and approx. 2 mm; 20 mirror sequins.
DRAWING OF SKIRT HANDLES
(the pattern is given at the beginning of the article in the photo series)
Translation of terms on the pattern:
Einreihen - pick up
Vordere u. rückwärtige Mitte - middle of the front and rear panels
Fadenlauf - thread direction
Radius for Waistline ®
SIZE 34 - 34 cm, size. 36 - 35.3 cm, size. 38 - 36.5 cm, size. 40 - 37.8 cm, size. 42 - 39 cm, size. 44 - 40.3 cm
Radius for Bottom Line (R1)
SIZE 34 - 104 cm, size. 36 - 105.3 cm, size. 38 - 106.5 cm, size. 40 - 107.8 cm, size. 42 - 109 cm, size. 44 - 110.3 cm
Using the drawing to make a paper pattern (a) in full size. To do this, draw a radius ® for the waist line and a radius (R1) for the line of the lower edge of the skirt on a large sheet of paper (the top and right edges should be a right angle) from the upper right corner with a thread compass. Or, put off the length of the skirt from the waistline down several times for the line of the lower edge and put points. Then connect the points with an arcuate line.
Allowances: for seams and cuts - 1.5 cm, for hemming - 3 cm.
CUT
a) cloth 2x according to the drawingSEWING
■ On the skirt, make the right side seam, iron the allowances.
■ For a zipper along the left side sections, measure 18 cm from the waist line and mark. Stitch a hidden zipper along the left side sections. Fill the left side seam from the bottom to the lower end of the zipper.
■ Picking up the upper section of the skirt to a width of 64–68–72–80–84 cm.
■ Belt.Tighten one end of the rep ribbon to a width of 1 cm and iron it. From this end of the tape measure 67−71−75−79−83−83−87 cm and put a mark. Place the rep tape from the inside out to the allowance along the upper cut of the skirt so that the ironed end of the tape protrudes at the rear edge of the cut under the zipper by 3 cm, mark the mark with the front edge of the cut. Lay a line along the bottom edge of the tape. Unscrew the tape on the face, rounding the front edge of the cut, chop off the longitudinal edges of the tape. In this case, the allowance for the upper cut of the skirt is between the halves of the tape. Tuck the other end of the tape. Sew the top edges of the tape to the edge.
■ Iron the bottom hem allowance to the wrong side and sew on by hand.
■ Stitch ribbons and braid on the skirt according to the model sketch or optionally for a total width of 30 cm. Stitch the bottom ribbon at a distance of 1.5 cm from the bottom edge of the skirt. In the middle of wide rep ribbons, sew along a narrow rep ribbon of a different color or along a narrow serrated braid. For quilling from a tape, lay the tape 3 cm wide in folds of 3 cm wide and sew it on the skirt, laying a line in the middle of the braid (at a distance of about 10 cm above the line of the lower edge). Sew the edges of the braid in the middle of each fold with one stitch, knit the ends of the threads in a knot (see step-by-step description above). Sew pearl beads in the shape of a wave. Sew mirror sequins over the top braid at the same intervals.
Layout plan
It is given at the beginning of the article in the series.
For fabric 150 cm wide
To lay out a fabric in one layer face up.
Material prepared by Elena Karpova

Send